Bios Info

[FONT="Arial"]Hallo liebes Forum,

also ich habe mal im ganzen Daten und Co. vom Bios aufgeschrieben bzw Fotografiert.[/FONT]


Advance

-> AI Tuning [Auto]
-> Voltage Control ---> CPU Vcore Offset Voltage [Disable]
-> PEG Link-Mode [Auto]
-> CPU Configuration ---> DRAM Configuration ---> Memory Clock Frequency [Auto]
---> 1T/2T Memory Timing [Auto]
Advance Memory Settings ---> DRAM Termination [Auto]
---> Max Async Latency [Auto]
---> R/W Queue Bypass [Auto]
---> Dynamic Idle Cycle Counter [Auto]
---> Idle Cycle Limit [Auto]
---> DCQ Bypass Maximum [Auto]
---> DRAM Brust Length [Auto]
---> RdPadRcvFIFO Delay [Auto]
---> Disable Jitter [Auto]
---> DRAM Bank Interleaving [Enabled]
---> Bank Swizzle Mode [Enabled]
-> DRAM Timing Control ---> Read DQS Timing Control [auto]
---> Write Data Timing Control [Auto]
---> DQS Receiver Enable Timing [Auto]

---> 1st Information 4-4-4-12-16
Tcl [Auto]
Trcd [Auto]
Trp [Auto]
Tras [Auto]

---> 2nd Information 4-2-4-2-2/4
Twr [Auto]
Trrd [Auto]
Trwt [Auto]
Twtr [Auto]
Trtp [Auto]

---> 3nd Information 1-2-2-7 .8us-1
Twrrd [Auto]
Twrwr [Auto]
Trdrd [Auto]
Tref [Auto]
Trfc [Auto]
-> Output Driver Control ---> Dram Drivers Weak Mode [Auto]
-> Chipset ---> CPU<->MCP55 HT Speed [5x]
---> CPU<->MCP55 HT Width [down16 up16]
-> PCIPnP ---> Plug&Play O/S [No]
---> Resources Controlled By [Auto]
-> Onboard Devise Configuration ---> IDE Function Setup ---> OnChip IDE Channel10 [Enabled]
I ---> IDE DMA transfer access [Enabled]
I ---> IDE Prefetch Mode [Enabled]
I---> Serial-ATA Configuration ---> Serial-ATA Controller [Enabled]
---> RAID Enabled [Disabled]
I---> USB Configuration ---> USB Controller [Enabled]
---> USB 2.0 Controller [Enabled]
---> USB Legacy support [Enabled]

Power:

-> ACPI Suspend Type [S1&S3]
-> ACPI ACPI support [Enabled]
-> AMP Configuration ---> Restore on AC Power loss [Power OFF]
---> PWR Button < 4sec [Instant OFF]
---> Power On By PCI/PCIE Devices [Disabled]
---> Power On By External Modem [Disabled]
---> Power On BY RTC Alarm [Disabled]
---> HPET Support [Enabled]
---> Power On By PS/2 Mouse [Disabled]
---> Power On By PS/2 Keyboard [Disabled]
->HardWare Monitor ---> CPU Q-Fan Control [Disabled]
--->xCPU Q-Fan Profile [Performance
---> Chassis Q-Fan Control [Diabled]
--->xChassis Q-Fan Profile [Performance]
---> Vcore Voltage [1,30V]
---> 3.3V Voltage [3,34V]
---> 5V [5,16V]
---> 12V Voltage [12,11V]
---> CPU Fan Speed Warning [600RPM]

Boot:

-> Boot Setting Configuration ---> Case Open Warning [Enabled]
---> Quick Boot [Enabled]
---> Boot Up Floppy Seek [Disabled]
---> Bootup Num-lock [On]
---> Typematic Rate Setting [Disabled]
---> OS Select For DRAM > 64MB [Non-OS2
---> Full Screen Logo [Enabled]
---> Halt On [ALL ERRORS]



Sooohh nach langer und schweißtreibenden Tipp-Akt habe ich es geschafft.
Und nu wollte ich wissen ob ich da was besser machen könne ? wäre für jede
Hilfe dankbar